NORTHTINTS.US • PRECUT PAINT PROTECTION FILM

Install your precut PPF kit

All NorthTints precut PPF kits are DIY kits designed for installation shops and PPF enthusiasts. Set up a clean work area and install one panel at a time. Read through the entire guide before peeling any liner.

Before you start a DIY installation

Every precut PPF kit requires controlled stretching to fit the vehicle’s contours. Do not start until you understand the full installation process.

As the DIY installer, you are responsible for learning how to prepare the panel, position the film, stretch it evenly, and finish the edges. Use this guide and look up DIY PPF installation videos on YouTube for the panel you’re working on before you peel the liner.

We’re here to answer questions. Because we can’t see or handle the film in person, we can’t guide you through the installation step by step. If you’re unsure how to proceed, pause and consult an experienced PPF installer.

Get ready

Tools and supplies

  • Two clean spray bottles marked Slip and Tack
  • Filtered or deionized water, approved slip agent, and 70% isopropyl alcohol if your film calls for it
  • Soft PPF squeegee, measuring syringe or cup, and lint-free microfiber towels
  • Paint-safe cleaner and, if needed, mild detailing clay with lubricant

Vehicle and workspace

  • Work indoors or in shade, away from wind and dust. The panel should be cool and within your film’s application temperature range.
  • Wash the vehicle and clean seams and edges. Remove wax and sealant with products approved for the paint. Ask an installer about coated, repainted, or damaged panels.
  • Identify each piece by its supplied diagram and keep the release liner on until installation.

Mix two solutions

Once you receive your kit, you are responsible for obtaining the supplies, mixing and adjusting the installation solutions, and installing the film, whether you do the work yourself or hire an installer.

Installing precut PPF takes practice. Shops and experienced DIY installers use controlled stretching to position the film around curves and secure the edges.

Our recipes are starting points. Panel temperature, humidity, and the film’s adhesive affect how the film slides and grips. In warmer conditions, the slip solution may need a small amount of additional soap. Add it in small increments and judge the mix by how easily the film moves while still allowing it to anchor. Follow the instructions for your specific film.

Use these as starting mixtures when your film’s instructions allow them. Always follow the instructions for your specific film.

SLIP · Position the film

32 fl oz water + 0.05–0.06 fl oz Johnson’s Baby Shampoo

Measure the shampoo and mix a fresh batch on installation day. If the film needs more slip, add a little more baby shampoo to the slip solution at a time. Adjust based on your workspace conditions and panel temperature, following your film’s instructions. Use slip on the panel and adhesive side to float the film into position.

TACK · Anchor the film

24 fl oz water + 8 fl oz of 70% isopropyl alcohol

Mix separately. Use tack at anchor points and edges where your film instructions call for it.

Optional installation tools

PPF installation gel

If your film allows it, use a compatible water-based installation gel for positioning in place of the slip mixture. Follow the gel instructions for application and squeegee it out as you work. Use the anchoring method recommended for your film.

Steamer

When your film allows steam, use gentle, brief passes to help the film conform around tight curves and, where directed, secure edges. Keep the nozzle moving and avoid overheating or forcing the film to stretch.

Watch a precut bumper installation on YouTube for a demonstration of positioning and working around curves. Follow the instructions for your specific film for mixtures, heat, and edge finishing.

Video credit: ENCORE Window Tinting & Paint Protection Film. Thanks to the original creator for sharing this tutorial. The video is freely available on YouTube. NorthTints.us shares the link as an instructional resource for installers and does not monetize the video.

Install one panel at a time

  1. Clean and inspect. Wipe the panel and its edges with a clean microfiber towel. Check seams for water or grit that could run under the film.
  2. Wet and peel. Wash your hands and wet your fingertips with slip. Spray the panel. Peel the release liner while spraying the exposed adhesive. Keep the adhesive away from clothing, the floor, and dry hands.
  3. Align. Float the piece on the wet panel. Use corners, openings, and body lines as reference points. For curved panels, stretch gradually and only as needed to match the pattern. If alignment takes excessive force, pause and ask for help.
  4. Set an anchor and squeegee. Flush slip away where you need to set an anchor, using the method approved for your film. Wet the face of the film so the squeegee glides. Use firm, overlapping strokes from the secured area toward open edges to move solution and air out.
  5. Finish the edges. Let solution drain, then set the edges and any wrap tabs supplied with your kit. Check for trapped liquid and lifting with light from the side. Keep blades away from painted surfaces and follow your film’s instructions for any heat or steam.

Inspect and care for the film

Before you finish

Check for creases, trapped grit, and lifting edges. If an edge keeps lifting or dirt is trapped under the film, stop and contact us or a professional installer before pulling or trimming the piece.

After installation

Follow your film maker’s cure and wash instructions. Hand wash gently and keep pressure spray away from film edges.

Questions before you start?

Have your order number and film name ready. If you need help with a particular piece, tell us which panel you’re working on and include photos through our contact page. You are responsible for installation whether you install the kit yourself or hire an installer.

Contact NorthTints